VT3000 - Install Paging Transmitter - Remote - Same Subnet

From Versacall Support
Revision as of 13:42, 22 August 2018 by SupportAdmin (talk | contribs)
Jump to navigation Jump to search

Overview

This guide will show how to configure a remote transmitter that is on the same subnet as the VersaCall computer/server. IT will need to provide a static IP address that can be used for this device.

Unpack

You will have the following components after unpacking.

  • Paging Transmitter

  • Power Cord

  • Serial Cable

  • Antenna

  • RS-232

  • RS-232 Power

  • Serial Cable

Instructions

    1. Connect the Serial Cable to the port on the Transmitter.
  • Trans14.png


    2. Connect the other end of the Serial Cable to the RS-232 device.
  • Coord15.png


    3. Connect the Power Cable to the Paging Transmitter.
  • Trans1.png


    4. Connect the Antenna to the Paging Transmitter.
  • Trans3.png


    5. Connect the Power Cable to the RS-232 device.
  • Coord16.png


    6. Connect the Ethernet Cable to the RS-232 device.
  • Coord17.png


    7. Connect the Ethernet Cable to your available port.
  • Coord18.png


    8. Connect both Power Cables to an Electrical Outlet.
  • Bscin4.png


    9. Go to the VersaCall Computer - open the VT3000 home page - select Administration – System Settings – Service.
  • HT3100 2.png
  • HT3100 3.png
  • HT3100 4.png


    10. Select the Paging Transmitter tab – select the add “+” icon.

Trans15.png 


    11. Use the settings below:

3102 9.png 

    a. Enabled – click on the box to place a check mark – this will enable the device.
    b. Description – enter any name for the transmitter.
    c. Driver – select the Salcom 12-62 - Remote driver from the list.
    d. Synchronization Code – if this is your only paging transmitter, leave the field as None. Use different codes for multiple transmitters.
    e. Connection Method – select TCP Client from the list.
    f. Address – click on the Scan button.



    12. The IP address of the RS232 device will show - click on the IP address - click on the Configuration button.

3102 10.png 


    13. Leave Password blank – select the Login button.

3102 11.png 


    14. Enter any name to identify the transmitter – select the Next button.

3102 12.png 


    15. Enter IP address information provided by your IT department – select the Next button.

3102 13.png 


    16. Use the settings below:

Trans16.png 

    a. Network Protocol – select TCP – select “to wait for connections”.
    b. Port Number – enter 4000.
    c. Limit – select 4 connections from the drop down list.
    d. IP Address – enter the IP address of the VersaCall computer.

NOTE: The IP address shown in the image is for reference purposes - use the IP address of your VersaCall computer/server. 


    17. Select the Advanced button.

3102 15.png 


    18. Use the settings below:

3102 16.png 

    a. Advanced – click in the box next to “I want to control when connections would be forced to close” to place a check mark in it.
    b. Network – click in the box next to “I want to close a connection” to place a check mark in it.
         i. Select “after the connection ……” and enter 2 in the field for minutes.
    c. Serial – uncheck the box and leave the milliseconds field blank.
    d. Data Packets – do not select the option to control data packets.



    19. Select the Next button.

3102 18.png 


    20. Use the settings below:

3102 17.png 

    a. Description – enter Serial Port 1
    b. Mode – select RS-232
    c. Baud Rate – select 9600
    d. Data Bits – select 8-Bits
    e. Stop Bits – select 1-Bit
    f. Parity – select No Parity
    g. Flow Control – select No Flow Control



    21. Select the Next button.

3102 18.png 


    22. Select the Save button.

3102 19.png 


    23. Close the VLinx webpage - select the IP address of the device - click on the Select button.

3102 10.png 


    24. Enter 4000 for the Port field.

3102 20.png 


    25. Select the Save & Exit button.

3102 21.png 


    26. Select Yes on the Restart warning message. This must be done to complete the setup.

3102 22.png 


    27. Restart the VersaCall Service - Click here for Instructions.

3102 25.png 


    28. Test the Transmitter - Click here for Instructions.


Having Trouble?

  • Submit a Service Ticket

Retrieved from "http://support.versacall.com/index.php?title=VT3000_-_Install_Paging_Transmitter_-_Remote_-_Same_Subnet&oldid=3827"