Difference between revisions of "VT3000 - Update Firmware - Manually"
SupportAdmin (talk | contribs) |
SupportAdmin (talk | contribs) |
||
Line 17: | Line 17: | ||
'''7.''' Using Windows Explorer navigate to the desktop - right click on the “0001_00.apk” file - select Copy. | '''7.''' Using Windows Explorer navigate to the desktop - right click on the “0001_00.apk” file - select Copy. | ||
8. | '''8.''' Navigate to the micro SD card – right click and select Paste. '''NOTE:''' do not alter or remove any of the files that show on the card. | ||
9. Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module. | '''9.''' Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module. | ||
10. | '''10.''' Move the sleeve - push down until it clicks in place. | ||
11. Connect power | '''11.''' Connect the 3 prong connector - plug in the power supply. After a 2 to 5 minutes the touch screen show a “Downloading Software” message. | ||
12. | '''12.''' A “Downloading Software Update” status bar will show. This bar will show the progress of the download - total download time should be about 15 to 20 minutes. | ||
13. | '''13.''' When the download is complete a VersaCall Installation screen shows – select the Install option in the bottom right corner. | ||
14. | '''14.''' After the install is complete the VersaCall screen will appear. If the Android home screen appears select the Home icon. | ||
15. Disconnect power from the I/O module. Remove the micro SD card as you did in step 5. | '''15.''' Disconnect power from the I/O module. Remove the micro SD card as you did in step 5. | ||
16. Insert the micro SD card into the reader | '''16.''' Insert the micro SD card into the reader. Open Windows Explorer if it does not open after inserting the micro SD card. | ||
17. Use Windows Explorer to find | '''17.''' Use Windows Explorer to find the 2 files from the zip file. Right click on the “LOADME.hex” file - select Copy. | ||
18. | '''18.''' Navigate to the micro SD card – right click - select Paste. '''NOTE:''' do not alter or remove any of the files. | ||
19. Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module. | '''19.''' Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module. | ||
20. | '''20.''' Move the sleeve - push down until it clicks in place. | ||
21. Connect power to the I/O module. | '''21.''' Connect power to the I/O module. | ||
22. The I/O module will only take 2 to 4 minutes to update. | '''22.''' The I/O module will only take 2 to 4 minutes to update. Check the Device Status to ensure the module shows the latest firmware version. |
Revision as of 00:56, 10 August 2017
Firmware updates are sent out with Software updates. This guide explains how to update firmware on the I/O Module and Tablet for PSM, TIM and BSC. Before starting this guide contact VersaCall Service to get a zip file containing the files needed for this process. A device that is able to read a micro SD card is required for this process. IMPORTANT – ALWAYS update the Touch Screen first then update the I/O module. Failure to do this will cause the Touch Screen to loose communication with the I/O module.
1. Unzip the file received from VersaCall - there will be 2 files “0001_00.apk” & “LOADME.hex” - place the files on the desktop.
2. Stop all processes and alarms on the module. NOTE: do not use the module until the update is complet.
3. Disconnect power from the I/O module - loosen the 4 screws from I/O module - remove the cover.
4. On the I/O board – locate the Micro SD card in the top right corner.
5. Remove the micro SD card - push up on the metal sleeve then pull down. When you push up the sleeve click. NOTE: do this step with care. If the sleeve is damaged the entire I/O module will need to be replaced.
6. Connect the Micro SD card reader to the computer - insert the micro SD card into the reader. Open Windows Explorer if it does not automatically open.
7. Using Windows Explorer navigate to the desktop - right click on the “0001_00.apk” file - select Copy.
8. Navigate to the micro SD card – right click and select Paste. NOTE: do not alter or remove any of the files that show on the card.
9. Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module.
10. Move the sleeve - push down until it clicks in place.
11. Connect the 3 prong connector - plug in the power supply. After a 2 to 5 minutes the touch screen show a “Downloading Software” message.
12. A “Downloading Software Update” status bar will show. This bar will show the progress of the download - total download time should be about 15 to 20 minutes.
13. When the download is complete a VersaCall Installation screen shows – select the Install option in the bottom right corner.
14. After the install is complete the VersaCall screen will appear. If the Android home screen appears select the Home icon.
15. Disconnect power from the I/O module. Remove the micro SD card as you did in step 5.
16. Insert the micro SD card into the reader. Open Windows Explorer if it does not open after inserting the micro SD card.
17. Use Windows Explorer to find the 2 files from the zip file. Right click on the “LOADME.hex” file - select Copy.
18. Navigate to the micro SD card – right click - select Paste. NOTE: do not alter or remove any of the files.
19. Remove the micro SD card from the reader – insert the micro SD card into the sleeve on the I/O module.
20. Move the sleeve - push down until it clicks in place.
21. Connect power to the I/O module.
22. The I/O module will only take 2 to 4 minutes to update. Check the Device Status to ensure the module shows the latest firmware version.