VT3000 - Install 2062 Paging Transmitter - Remote - Ethernet Connected

From Versacall Support
Jump to navigation Jump to search
Call Now 858-677-6766 SubmitTckBtn.png EmailUsBtn.png



GeneralHeader.png

Overview
A Paging Transmitter is used to send messages to individual Pagers. This guide will show how to configure a NEW 20-62 paging transmitter being connected to a Network (Ethernet) Port. Prior to installation, IT will need to provide a static IP address to VersaCall for setup. The 20-62 Remote Paging Transmitter will come Pre-Programmed when using an Static IP Address.
For a DHCP Reserved Address, the MAC Address can be provided by VersaCall prior to shipping or IT can setup it up once the transmitter is received. The Transmitter will come with a label that has the MAC Address printed on it.


Requirements
See Requirements Here
1. The Current VT3000 Core Software installed and running on your system. Software versions prior to 2022 will not have the driver loaded for the New 20-62 Paging Transmitter.
2. VersaCall Computer/Server plugged into your network via Ethernet connection.
3. Paging Transmitter hardware.
4. For DHCP Reserved Adresses, IT Department will need to be present to set it up.
5. Open Ethernet port in the mounting location for the Paging Transmitter.
6. One 110VAC outlet for power in the mounting location for the Paging Transmitter.


Hardware Components
2062-All-Parts.png



InstructionHeader.png

Step 1.
Connect the Ethernet Cable to the available port on the side opposite of the antenna port.
2062-Step1.png
2062-Step1B.png



Step 2.
Connect the green Power Cord connector to the available port - same side as Ethernet Cable.
2062-Step2.png



Step 3.
Screw on the Antenna to the available connector - opposite side as Ethernet & Power connnections.
2062-Step3A.png
2062-Step3B.png



Step 4.
Connect the Ethernet Cable to an available port on your network.
2062-Step4.png



Step 5.
Connect the Power Cable to an available Electrical Outlet.
2062-Step5.png



Step 6.
Go to the VersaCall Computer - open the VT3000 home page - select Administration – System Settings – Service.
HT3100 2.png HT3100 3.png HT3100 4.png



Step 7.
Select the Paging Transmitter tab – select the add “+” icon.
Trans15.png



Step 8.
Use the settings below:
2062-Driver.png
Enabled – click on the box to place a check mark – this will enable the device.
Description – enter any name for the transmitter.
Driver – select the Salcom 20-62 driver from the list.
Synchronization Code – leave this set to None.
Connection Method – select TCP Client from the list.
Address – type in the IP Address of the 20-62 transmitter. This will be either the Static IP Address that was pre-programmed or IT will provide the IP Address that was setup as DHCP Reserved.
Port - enter 4000.



Step 9.
Select the Save & Exit button.
3102 21.png



Step 10.
Select Yes on the Restart warning message. This must be done to complete the setup.
3102 22.png



Step 11.
Restart the VersaCall Service - Click here for Instructions.
3102 25.png



Step 12.
Test the Transmitter - Click here for Instructions.



RelatedHowTos.png
Select a Guide Here
Find the Paging Transmitter Properties/Settings
Install a USB Paging Transmitter
Replace an Existing USB Paging Transmitter
Install a 2062 Paging Transmitter - USB Connection
Install a Remote Paging Transmitter on a Different Subnet
Test Paging Transmitter Coverage
Programming a New Capcode on a Pager
Add a Pager to Output in VT3000 Core Software



SearchHeader.png

 



VC Footer.png
Follow Us On LinkedIn View our Blog


Retrieved from "http://support.versacall.com/index.php?title=VT3000_-_Install_2062_Paging_Transmitter_-_Remote_-_Ethernet_Connected&oldid=9916"